1:  da16cb2e47ec = 1:  a6088292acf9 bcma: core: clear only FORCEHT for BCMA_CLKMODE_DYNAMIC
2:  62a383171a16 = 2:  796f7c359d0a bcma: pmu: init PLL and resources on BCM4352/BCM4360
3:  a02df96f62a1 = 3:  b68912a53b32 bcma: pcie2: request HT on BCM4352/BCM4360
4:  57c4563a1817 ! 4:  1efec9261d87 bcma: chipcommon: set corecontrol bits 5:2 on BCM4352/BCM4360
    @@ Metadata
     Author: Alessio Ferri <alessio.ferri@mythread.it>
     
      ## Commit message ##
    -    bcma: chipcommon: set corecontrol bits 5:2 on BCM4352/BCM4360
    +    bcma: chipcommon: enable asynchronous GPIO interrupts
     
    -    Set them in chipcommon init, as Broadcom's driver does.
    +    Set CORECTL_ASYNCGPIO on chipcommon rev 21 and later, as Broadcom's
    +    driver does at attach, so that GPIO interrupts are generated without the
    +    backplane clock.
     
         Signed-off-by: Alessio Ferri <alessio.ferri@mythread.it>
     
    @@ drivers/bcma/driver_chipcommon.c: void bcma_core_chipcommon_init(struct bcma_drv
      			 (leddc_off << BCMA_CC_GPIOTIMER_OFFTIME_SHIFT)));
      	}
     +
    -+	/* Corecontrol bits 5:2: bit 3 is UARTCLKEN, the rest undocumented. */
    -+	if (cc->core->bus->chipinfo.id == BCMA_CHIP_ID_BCM4352 ||
    -+	    cc->core->bus->chipinfo.id == BCMA_CHIP_ID_BCM4360)
    -+		bcma_cc_set32(cc, BCMA_CC_CORECTL, 0x3c);
    ++	if (cc->core->id.rev >= 21)
    ++		bcma_cc_set32(cc, BCMA_CC_CORECTL, BCMA_CC_CORECTL_ASYNCGPIO);
      	cc->ticks_per_ms = bcma_chipco_watchdog_ticks_per_ms(cc);
      
      	cc->setup_done = true;
    +
    + ## include/linux/bcma/bcma_driver_chipcommon.h ##
    +@@
    + #define BCMA_CC_CORECTL			0x0008
    + #define  BCMA_CC_CORECTL_UARTCLK0	0x00000001	/* Drive UART with internal clock */
    + #define	 BCMA_CC_CORECTL_SE		0x00000002	/* sync clk out enable (corerev >= 3) */
    ++#define  BCMA_CC_CORECTL_ASYNCGPIO	0x00000004	/* GPIO IRQs without backplane clock */
    + #define  BCMA_CC_CORECTL_UARTCLKEN	0x00000008	/* UART clock enable (rev >= 21) */
    + #define BCMA_CC_BIST			0x000C
    + #define BCMA_CC_OTPS			0x0010		/* OTP status */
5:  247bb8843b4b = 5:  ace78e47aa23 bcma: extract SPROM revision 11
6:  c362977aaac7 = 6:  a03d620da9d5 firmware: bcm47xx_sprom: read ledbh4..ledbh15 from NVRAM
7:  7a4046610965 = 7:  62b3cd290824 firmware: bcm47xx_sprom: read boardflags3 and AvVmid_c0..2 from NVRAM
8:  4d3da32385b2 = 8:  027005b86b3a bcma: add the BCM4352 PCI ID